Hot Spring Spas
Do not fill the spa with hot water, as tripping of the high-limit thermostat may result . DO NOT CONNECT POWER TO AN EMPTY SPA. Power to the spa automatically activates critical components within the spa, such as controls, heater, and other systems. If power is supplied to these components prior to the spa being filled. Located across the road from the Mineral Baths is the Hot Springs Campground. Here you can find peace of mind with ease and comfort. We feature eight primitive camping cabins, over a hundred tent sites (primitive, group & sites with partial hook up) & Full RV Hookups. On site comfort station features hot showers . HIGHLIFE NXT OWNER'S MANUALS. The Highlife NXT Collection Owner's Manual will help you understand your spa’s features, and answer questions you might have regarding spa operation, water care, and maintenance. The Highlife Collection Owner's Manual will help you.
Always clean and rotate the filter cartridges each time the spa is drained for cleaning. We have four luxury suites that have a Jacuzzi style tub with mineral water in the room. Than reset the 30 amp breaker.
Hot Spring Spas Jetsetter Hot Tub Installation by Creative Energy
Always clean and rotate the filter cartridges each time the spa is drained for cleaning. LA Spa close-out sale!
Find out what the Trade In Value may be and consider trading in your old hot tub for an additional discount! Hours Monday - Friday 9: Locate the main drain valve for the spa and remove the drain cap. Attach the inlet of a garden hose to the drain valve to avoid flooding of the foundation surrounding the spa and route the outlet of the hose to an appropriate draining area.
Spa water with a high sanitizer level may harm plants and grass. Open the valve Hot Springs Hot Tub Hook Up turning the knob. The spa will drain by gravitational flow. All Hot Spring spa models will drain almost completely through the main drain valve and the secondary drain. Equipment such as the jet pump and heating system will drain.
Any water remaining within the plumbing or equipment after draining will only need to be removed if the spa is being winterized. Allow most of the water to drain through the main drain. Remove threaded cap from secondary drain. This will drain the remaining water about one gallon from the bleedline system. Close the drain valve and reinstall the drain cap.
Reinstall threaded cap onto secondary drain. Power to the spa automatically activates critical components within the spa, such as controls, heater, and other systems.
If power is supplied to these components prior to the spa being filled, the components will be damaged, and this may result in a non-warranty component failure.
Do not use your spa after filling until all of the steps listed below are completed.
Before filling your spa for the first time, remove the equipment compartment door and check to ensure that the unions on either side of the pump s and heater are hand-tight. This will minimize airlocks in the equipment by filling through the heater, pumps and jets, pushing most of the air out of the lines.
AFTER the spa has been filled with water and the equipment compartment door is secured, power must be applied to the spa. Than reset the 30 amp breaker. The jet pump sheating system and all internal plumbing will achieve a partial prime as the spa is filled. Once the jet system is fully operational as indicated by strong, non-surging jetspriming of the spa is complete.
Weak or surging jets are an indication of a low water level condition or clogged filter cartridges. Add spa water chemicals directly into the filter compartment with the jet pump on high speed for at least ten minutes. Adjusting the Total Alkalinity as the first step is important, as out-of balance TA will affect your ability to adjust the pH correctly and will prevent the sanitizer from operating effectively.
The jet pump should be running on high speed when adding the chlorine, and remain on high to circulate the spa water for a ten-minute period. Make sure you secure the cover in place using the cover locks. Periodically check the spa water temperature. Hot tubs on V may take up to 36 hours to heat Hot tubs on V may take up to 12 hours to heat on average Run the CLEAN cycle, or jets on high for 10 minutes to circulate the spa water.
Power to the spa automatically activates critical components within the spa, such as controls, heater, and other systems. Make sure you secure the cover in place using the cover locks. Reinstall threaded cap onto secondary drain. On site comfort station features hot showers seasonal and clean bathrooms.
If the residual is Hot Springs Hot Tub Hook Up 3 and 5 ppm on the test strips found in most chemical test kit go on to the next step. Make sure you adjust your Total Alkalinity first, as an out-of-balance condition will affect your ability to adjust the pH correctly, and will prevent the sanitizer from operating effectively.
The spa is ready for use when the spa water has circulated and the chlorine level remains between 3 ppm and 5 ppm.
The spa temperature is pre-programmed to reach F, and will normally do so within 18 to 24 hours. Whenever the jet pump has been turned off and a three-degree temperature drop has occurred or the temperature control has been turned up, it will take ten minutes before the low speed of the jet pump and heater become activated. Always push the JETS button to turn off the jet pump when exiting the spa.
In the standard volt, 15 or 20 amp electrical configuration, the heating system does not operate simultaneously with the high speed pump. On the other hand, on the volt system, the heating system does operate simultaneously with the high speed pump.
Hot Springs Hot Tub Hook Up six hours here continuous operation, the controller will automatically turn the light off.
Drain and Refill your Hot Tub 2 - 4 times a year. Do not drain your hot tub in temperatures below 40 degrees! Featured Specials LA Spa close-out sale!
Trade In Value Find out what the Trade In Value may be and consider trading in your old hot tub for an additional discount!